INSTALLATION GUIDE

How to Install Backlit Channel Letters

Use the supplied Installation Template to position the letters, drill the mounting holes and wire openings, preserve the specified stand-off clearance, connect the low-voltage plug and play wires, and test the halo effect.

This installation video demonstrates individual, direct-mounted backlit letters.

backlit installation hero 1200x675 1 - How to Install Backlit Channel Letter Signs

WATCH THE PROCESS

Watch the Installation Video

Video chapters

0:20

Position the full-size Installation Template

0:31

Level and tape the template

0:48

Confirm the marked hole locations

0:52

Drill the marked openings

1:09

Remove the Installation Template

1:16

Inspect the letter back and hardware

1:40

Mount the first individual letter

1:54

Place the remaining letters

2:12

Connect the low-voltage letter leads

3:16

Secure the power supply

3:39

Test the halo illumination

QUICK ANSWER

Backlit Channel Letter Installation: Quick Answer

STEP 1

Install the Letters

A direct-mounted backlit sign is installed one letter at a time. Tape and level the full-size Installation Template, mark and drill the specified mounting and wire openings, then route each letter’s lead and secure its stand off hardware. Keep the specified gap behind the letters for the halo effect.

STEP 2

Connect and Test

From the service side, connect the individual letter leads to the supplied low-voltage harness. Secure the power supply in its approved location, complete the required building-power and wall details, then check that every letter produces an even halo light.

How to Install Backlit Channel Letters

backlit installation step 01 - How to Install Backlit Channel Letter Signs
- How to Install Backlit Channel Letter Signs

VIDEO REFERENCE: 0:20

Position and Level the Installation Template

Tape the supplied full-size 1:1 Installation Template at the approved sign location. Check the overall width, baseline, centerline and surrounding clearances. Level the template, then recheck measurements before transferring any hole locations.

Installer check: Do not assume a nearby storefront frame or wall edge is leveled. Set the sign from the approved reference dimensions.

- How to Install Backlit Channel Letter Signs

VIDEO REFERENCE: 0:48

Mark and Drill the Mounting and Wire Openings

Drill the specified mounting points and wire-pass locations through the template. Confirm the marks against the letter layout and avoid known utilities or prohibited areas. Drill only after identifying the wall assembly and approved bit, hole size, anchor and penetration detail.

backlit installation step 02 - How to Install Backlit Channel Letter Signs
backlit installation step 03 - How to Install Backlit Channel Letter Signs
- How to Install Backlit Channel Letter Signs

VIDEO REFERENCE: 1:16

Check Each Letter and Its Stand-Off Hardware

Identify the correct letter and inspect its back, low-voltage lead and supplied mounting parts. Screw the threaded screw rods to the back of the letters and logos. Place the spacers in to the screw rods. Apply silicon glue to the threaded screws. The specified clearance behind the letter allows light to wash onto the wall.

Spacing: Use the stand-off depth approved for the order. The video does not specify one universal gap for every installation.

- How to Install Backlit Channel Letter Signs

VIDEO REFERENCE: 1:40

Route the Lead and Mount Each Letter

Feed each letter’s low-voltage lead through its prepared opening without pulling on the internal connection. Support and align the letter, seat the letter in to the installation surface by inserting the threaded screw rods of each letter in to the drilled holes, and secure it to the mounting surface. Repeat for the remaining letters while keeping their spacing consistent.

Handling: Support the letter while routing its lead. Do not let the letter hang from the wire.

backlit installation step 04 - How to Install Backlit Channel Letter Signs
backlit installation step 05 - How to Install Backlit Channel Letter Signs
- How to Install Backlit Channel Letter Signs

VIDEO REFERENCE: 2:12

Connect the Low-Voltage plug and play wires

From the service side of the wall, organize the individual letter leads and connect them to middle wire of the supplied plug-and-play T-wires. Then connect each end of the T-wires with each other in series connection. connect the last T-wire to the Transformer.

- How to Install Backlit Channel Letter Signs

VIDEO REFERENCE: 3:16 & 3:39

Secure the Power Supply and Test the Halo

Secure the power supply in the approved protected and serviceable location. Mount the power supply in the protected and serviceable location. Connect the power supply to the power source. Turn the power on and confirm to check that every letter produces an even halo.

backlit installation step 06 - How to Install Backlit Channel Letter Signs

MOUNTING AND HALO

Why Stand-Off Spacing Matters

The approved gap behind each backlit letter lets light wash onto the wall creating a halo effect

THIS VIDEO

Individual Direct Mount

The letters attach individually with the specified stand-off hardware. Their rear illumination reflects from the wall to create a halo. Check the approved spacing and keep it consistent across the sign.

OTHER SYSTEMS

Raceway or Backer Panel

A raceway or backer-panel order has a different attachment and wiring layout. Use the shop drawing and instructions supplied with that mounting system rather than applying the direct-mount sequence shown here.

BEFORE HANDOFF

Final Inspection

backlit installation final check - How to Install Backlit Channel Letter Signs
  • The wordmark and individual letters are leveled, evenly spaced and oriented correctly.
  • Each letter is secured.
  • Required exterior penetrations are sealed and the wall system remains weather-managed.
  • Wiring is protected, supported and kept away from sharp edges.
  • The power supply is secure, protected and serviceable as required.
  • Each letter has an even halo without unexpected dark areas; document the completed test.

TROUBLESHOOTING

If a Letter Has No
Halo

- How to Install Backlit Channel Letter Signs

Turn the power off before inspecting connectors or enclosures.

- How to Install Backlit Channel Letter Signs

Compare the connections with the project wiring diagram and confirm each approved connector is fully seated.

- How to Install Backlit Channel Letter Signs

Check for pinched, cut, unsupported or misrouted low-voltage wires.

- How to Install Backlit Channel Letter Signs

Have a qualified person verify the power supply and building-power side with suitable test equipment.

- How to Install Backlit Channel Letter Signs

Contact ChannelLetter.com support with the order information, photos and a description of the issue before replacing components.

Backlit Channel Letter Installation FAQs

The video shows individual, direct-mounted backlit letters on an open-wall training setup. It does not demonstrate raceway or backer-panel installation.
The approved stand-off clearance lets light from the rear of each letter wash across the wall to create a halo. Use the spacing specified for your order.
The full-size Installation Template establishes the sign’s position and transfers the intended mounting and wire-pass locations to the wall. Confirm its centerline, dimensions and level before drilling.
They must match the actual wall construction, loads and approved mounting detail. The video does not specify a universal anchor or bit.
Use the secure, protected and serviceable location shown in the project electrical plan, with the required access and clearances.
Follow the approved detail for the wall assembly. The demonstration does not show completed exterior waterproofing, flashing or sealant work.

Turn the power off before inspection. Check spacing and the supplied connection path against the project drawing, then have a qualified person diagnose the power side. Contact ChannelLetter.com support with photos and order details before substituting components.

No. Raceway and backer-panel systems use different mounting and wiring arrangements. Follow the instructions supplied for that system.

START YOUR PROJECT

Ready to Design Your Back Lit Sign?

Design in minutes using our easy online sign designer.

Click here if you have a Custom Design or need help with your Sign Design.